Industrial Catalysts And Chemical

Product Details:

• Carbon Molecular Sieves For PSA Nitrogen Plant

• is a new non-polar adsorbent in the PSA nitrogen generator, can adsorb oxygen molecules at the normal temperature, and thus available to get the abundant nitrogen and its principle is to use screening to achieve the separation of oxygen, nitrogen purpose.
• The most striking characteristics of Carbon Molecular Sieve is: less impurity in N2 products, N2 purity and volume can be adjusted as needed and can be obtained by refining O2 content of less than 5PPM.

Product Details:

• Production of Endo gas for steel treatment.
• High cold crushing strength
• Low-pressure drop.

• Avoid damping and any adsorption of water or organic substance before use. Otherwise it must be regenerated. 

• Size :-18-20,20-25mm 
• Bulk Density:-1.3 + 0.1Kg/litter

Product Details:

• Nickel Catalyst is provided with the properties. It is used in the ammonia decomposing furnace to decompose the HN3 and HCN into N2, H2 and CO2. And so as to effectively purify the coke-oven gas for the sake of environmental protection and prevent the equipment from corrosion.

Product Details:

Classification: Catalyst

1.Palladium content: 0.3%, 0.5%, 1.0%
2. Palladium catalyst Grade: Industrial grade
3. Palladium catalyst Granularity: 100mesh(or following your demand)
4. Moisture: ≤ 3.0%
5. Features: Good hydrogenation conversion, selectivity and stable performance
Operation instructions:-

The product is already activated and could be loaded and used directly. Whether should the deoxy genate be pre-heated (to 50-80 ° C) or not depends onoxygen content in raw gas. The working temperature should be lower than 450 ° C
Specifications:
Appearance: Coconut shell flake
Pd content: 0.48-0.52
Particle size %: ≥ 95
Crushing strength: ≥ 40
Specific surface area: 1000-1300
Bulk density g/ml: 0.4-0.5
Abrasion %: ≤ 1
Reaction recovery %: ≥ 99

Technical Specification

Use:
Nitrogen or argon separated from air could be purified up to 1 ppm oxygen content after on deoxygenating step. The oxygen content can be reduced to 0.1 ppm. Palladium catalyst Application: It's a kind of high efficient deoxidizer, Can be used for hydrogen, nitrogen and argon, krypton etc. Various gas the depth purification. Widely used in metallurgy, chemical industry, light industry, electronic industries

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: All over india
• Delivery Time: As Per client
• Packaging Details: As Per Client requirements

Product Details:

• We are extremely engaged in providing Copper Catalyst for Nitrogen Deoxo. These products are recognized in the market for their top features.
• Copper catalyst for PSA Nitrogen Generator Copper De-Oxo
• Genuine deoxo copper catalyst for your nitrogen generator
• Guaranteed performance
• Irrespective of which make Nitrogen generator you have, we can supply you the correct copper catalyst

• For production of high purity gases such as Nitrogen, requires use of high activity catalysts for the removal of impurities. Oxygen is a major impurity in inert or reactive gases and therefore reducing its concentration is a subject of continual interest. Chemisorption with subsequent catalytic reaction always offers an economical and effective way to purify gases. Copper catalysts are frequently used in the above described applications. The goal of using copper catalyst is the removal of oxygen from nitrogen, thereby delivering high quality inert gas with ppm levels of Oxygen remaining.

• Copper catalyst removes oxygen from gases containing a maximum of 1.0 to 1.5 vol.% O2. In this case, it is possible to achieve a purity of 1-5 ppm. For the adsorption of oxygen, room temperature is sufficient. The total amount of oxygen that is absorbed by the catalyst, however, largely depends on the temperature.

• Catalyst is always supplied in unreduced state.

• The catalyst can be activated in either a tubular reactor with heat exchange or in an adiabatic-type reactor. The reduction starts in either reactor by heating the catalyst in a stream of nitrogen to a temperature of 140 to 160°C. Subsequently, hydrogen is added to the nitrogen at such a rate that a temperature of 250°C is not exceeded. The reduction should be completed at a temperature of min. 230°C with undiluted hydrogen.

Product Details:

We do not provide Used Palladium Catalyst

Palladium Catalyst.

Classification: Catalyst.

1. Palladium content: 0.3%, 0.5%, 1.0%
2. Palladium catalyst Grade: Industrial grade
3. Palladium catalyst Granularity: 100mesh(or following your demand)
4. Moisture: ≤ 3.0%
5. Features: Good hydrogenation conversion, selectivity and stable performance

Operation instructions:

The product is already activated and could be loaded and used directly.
Whether should the deoxy genate be pre-heated (to 50-80 ° C) or not depends on the oxygen content in raw gas.
The working temperature should be lower than 450 ° C

Specifications:

Appearance: Palladium Catalyst Coated on alumina

Pd content: 0.48-0.52
Particle size %: ≥ 95
Crushing strength: ≥ 40
Specific surface area: 1000-1300
Bulk density g/ml: 0.4-0.5
Abrasion %: ≤ 1
Reaction recovery %: ≥ 99

Technical Specification:

Use:

Nitrogen or argon separated from air could be purified up to 1 ppm oxygen content after on deoxygenating step.
The oxygen content can be reduced to 0.1 ppm.

Palladium catalyst Application:-

It's a kind of high efficient deoxidizer, Can be used for hydrogen, nitrogen and argon, krypton etc. Various gas the depth purification. Widely used in metallurgy, chemical industry, light industry, electronic industries.

Storage:

Avoid damping and any adsorption of water or organic substance before use. Otherwise it must be regenerated.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: All over india
• Delivery Time: As Per client Requirements